HVAC repairs and updates vary based on homeowners’ needs and home specifications
Q. My old HVAC system needs major repairs. What are my options, and what factors should I consider when selecting a new system?
A. Many factors are specific to your house, such as the floor-plan layout, the number of floors, orientation to the sun/ shade, wind conditions, etc. Others are personal, such as individual room temperature control, noise level or speed to reheat after a thermostat setback. Make sure to discuss these with your HVAC contractor.
You have many fuel options for the heating portion of your new system — electricity, oil, propane, gas, firewood, corn, wood pellets and coal. Although there are some larger gas-absorption cooling systems available, typically, your only option for cooling is electric-powered central air-conditioning or a heat pump.
Initial installation and operating costs are usually the primary factors in selecting a new system. Often spending more initially can result in a substantial payback with lower operating costs over the life of the new system. Keep in mind that various fuel prices can vary significantly over time, so payback estimates are a guess, at best.
Efficiency is the other factor in determining operating costs. Most new HVAC systems are operating at extremely high efficiencies now, so I would not expect any major design innovations to significantly increase future efficiencies. Repairing your old system in order to wait for new designs is not a wise decision.
A geothermal heat pump is still the most efficient year-round system because it heats and cools using stored energy from the ground. I installed a 4-ton Water Furnace model with a backup electric furnace in my own home four years ago.
Select a variable-speed model for the best comfort and lowest operating costs. When coupled with a smart thermostat, the system continuously matches heating and cooling output to the instantaneous house needs. This means the compressor and blower fan run in longer cycles or almost continuously at very low speeds for extremely quiet operation and steady room temperatures.
The initial cost of a geothermal system is substantially more than other complete systems, but the utility-bill savings easily pay back the amount spent on the system’s higher cost. The federal energy-tax credit is 26 percent in 2020 and will drop to 22 percent in 2021. Also, check for some state- or utility-company-backed credits.
If you plan to install a fossil-fuel (gas, oil or propane) furnace for heating, install a matching heat pump with it instead of just a central air conditioner. Some manufacturers refer to this as a hybrid system. A heat pump is basically a central air conditioner with a reversing valve and other controls for heating. It costs only several hundred dollars more.
Since it draws heat from the outdoor air, a heat pump heats efficiently during mild spring and fall weather. It runs instead of the furnace burners to heat the house at a lower cost. When it gets colder outdoors, the furnace burners take over. A heat pump cools as efficiently as a central air conditioner during summer.
If natural gas is available in your area, a condensing furnace generally is the most cost-effective fossil-fuel choice. With the glut of domestic natural gas from fracking, there should be an adequate supply at reasonable prices for the foreseeable future. Efficiencies are as high as 97 percent with sealed combustion.
Since natural gas is not available in many rural areas, a propane or oil furnace provides equally comfortable heating. A propane furnace is almost identical to a gas one, but propane is typically more expensive to use and can be in short supply at times. Oil is readily available, but oil-furnace efficiency is not as high, and the furnace requires a more extensive maintenance schedule and cost.
Also consider alternative fuels such as firewood, corn, wood pellets, etc. for primary or supplemental heating. Newer models are convenient to use, and the fuel is renewable to reduce your carbon footprint. For example, new dual-fuel wood furnaces automatically switch to gas or propane when the wood burns out overnight.
To compare operating costs of various fuels, use the following heat contents and your local fuel costs: natural gas, 1,025 Btu/ cubic foot; oil, 138,700 Btu/gallon; propane, 91,000 Btu/gallon; electricity, 3,414 Btu/kilowatt-hour; firewood, 22,000,000 Btu/cord; and corn, 448,000 Btu/bushel. Divide your local cost per Btu by the various system efficiencies to compare operating costs.
Q. When I build on an addition to my home, I plan to use rigid foam insulated sheathing on the outside. Will it harm the efficiency to use more nails and fasteners for a stronger wall?
A. Adding more nails and metal fasteners than recommended by the manufacturer does not produce a better wall. In fact, using more nails decreases the effectiveness of the rigid foam insulation. Steel nails are a great conduction of heat. Tests show that using just the recommended number of nails and fasteners (on 8-inch centers) reduces the insulation value by 20 percent.
Send inquiries to James Dulley, Arkansas Democrat-Gazette, 6906 Royalgreen Drive, Cincinnati, OH 45244; or visit dulley.com.