The many problems with floor protectors
Here’s some advice for a reader on what to do about floor protectors that won’t stay in place.
Q We have protective coverings for the bottoms of the legs of our kitchen chairs, but the product we use does not stay in place even with an additional cushion underneath. We tried gluing the protectors in place, but that presented another problem when the sliders still came off and the glue stuck to the hardwood floor. Also, the sliders are made of felt and have caused wear to the hardwood. We have thought about using a rug under the kitchen table but that would make cleaning more difficult. Do you have any ideas?
A Felt floor protectors are a great — maybe the best — way to keep chair legs from scratching a hardwood floor, but only if the felt stays on and hasn’t picked up a lot of grit. Manufacturers have come up with various ways of holding the felt in place: adhesives,
Multiple layers of padding increase the risk that the layers won’t stay on, so pick just one type.
nails and other fasteners, and even flexible slip-ons. Each type has its advantages and disadvantages.
Multiple layers of padding increase the risk that the layers won’t stay on, so pick just one type.
Adhesive-backed felt pads, the most common option, have the advantage of being easily replaceable when the felt picks up a lot of grit. When the pads don’t stick, there could be several reasons. If the bottoms of your chair legs have adhesive residue or are gritty or oily, clean the surface first with denatured alcohol. If the wood is splintered, perhaps because a nail-on protector was once pried off carelessly, use wood filler and sand it smooth once it dries. Old, dried-out pads and some cheap options don’t stick well; try ones made by a company noted for its research into adhesives, such as Scotch ($6.48 for 16 square pads at walmart.ca; or $6.49 through amazon.ca). On chairs with square legs such as yours, square felt pads give a tidier look than round pads, although either shape functions just as well. If you use round pads or glides, the diameter should be slightly smaller than the leg.
Sometimes felt pads won’t stay on a specific leg, even though they stick well to other legs. In this case, the chair also probably wobbles because the problematic leg is a bit too short or it’s cut so that it doesn’t sit flat against the floor. Remove all of the protectors and push a wooden shim under the errant leg until the chair no longer wobbles. Then trace around the leg and cut the shim to fit. Glue it in place. Once the glue dries, add extra muscle by installing nail-on floor protectors on all four legs. The nail and pad also will help hold the shim in place on the problematic leg. When chair legs angle out (not the case on your chairs), swivel-type glides with felt pads work best. (A four-pack of oneinch diameter nail-on felt swivel glides from Shepherd Hardware Products is $6.91 at amazon.ca.)
Nail-on protectors come in two main types: with nails and with a short bit of round tubing that you hammer into the bottom of the chair leg. It’s important to pre-drill for the nail type so that you don’t split the wood. Install the tubing type with a few taps of a hammer; no drilling. If you’ve previously used one type but the protectors don’t stay on, try switching to the other type. Or first fill the previous holes with wood filler strong enough to hold nails and screws once it cures. If even that doesn’t allow you to attach nail-on protectors securely, switch to a different type. When nail-ons come loose, they can definitely scratch wood floors.
The third type of protector, slipons, are designed to get around the problems of adhesives and nails. Depending on the brand, these consist of a flexible silicone or PVC plastic sock with a felt pad as the sole. If you get slip-ons sized to fit your chair legs, they should stay on flawlessly.
All Glides sells PVC caps; ones for square legs 1¼-inch diameter are $1.18 each. Among the silicone types, the Melonboat Protectors for square legs of 1¼ to 1⅜ inches cost $26.99 for a package of 16 on Amazon.
Whatever your solution, you need to keep the felt free of grit or your floor will get scratched. Sweep, dust-mop or vacuum the floor frequently. It also helps to reach under the legs periodically to detect grit.
And if you conclude that nothing short of covering the wood will protect your floor? One elegant solution that’s also easy to clean is an oilcloth-type floor mat big enough to fit under your table and chairs. Search online for “floor cloth” and you’ll find directions for making one yourself, or you can order one from artists who have revived the craft of making floor coverings from canvas or other materials and paint.