Getting handy ... all in a day
Four do-it-yourself projects that can be completed quickly with basic tools
Think you don’t have the time to tackle a home improvement project? Good news: There are a number of easy renovations you can do in one day — without the help (or cost), of a handyman or contractor. Here are four that you can do with just a few basic tools.
RECAULK A SHOWER
What you’ll need: Caulk remover A utility knife Painter’s tape Caulk
A caulk gun A damp towel
Over time the seal around a bathtub or shower can wear, discolour or crack, allowing moisture to pool inside and creating a perfect environment for mould and mildew to grow. But recaulking is easy, says Mark Clement, co-founder at MyFixitUpLife. com, a resource for DIY home remodelling.
It’s up to you whether you want to use latex or silicon caulk. Latex shrinks more than silicone caulk, but it’s easier to smooth and clean up.
First use a caulk remover to soften the existing caulk; this will prep the surface and make it easier for you to remove the caulk using a utility knife with a fresh blade. Once all the old caulk has been removed, use a damp cotton rag to clean away dust. Let the surface air-dry completely.
The caulk line you’ll create is called a bead. To create an even bead, lay parallel strips of painter’s tape above and below the entire length of the tub seam. Then load the caulk into a caulk gun, point the nozzle at a 45-degree angle and apply steady pressure to the trigger as you move along the seam.
Finally, slide a finger along the joint to smooth the bead, remove the tape while the caulk is still wet, and let the caulk cure for at least 24 hours before using the shower or bath.
INSTALL SHOWER HEAD
What you’ll need: A new shower head An adjustable wrench Plumber’s tape A toothbrush Vinegar
If your shower head has low water pressure, a deep cleaning may unclog it. But if you’re ready to upgrade to a rainfall shower, or a shower head with relaxing massage jets, you can replace the old head in less than 20 minutes, home improvement and DIY expert Beth Allen says.
First, turn off the water. Then use an adjustable wrench to loosen and unscrew the old shower head. Once the head is off, remove any old plumber’s tape and scrub the threaded connection between the shower head and the joints, using a toothbrush dipped in vinegar, to clean away rust or mineral deposits.
“If mineral deposits are present when you put a new shower head on, you’re not going to get a tight seal,” Allen says.
Wrap plumber’s tape in a clockwise direction two or three times around the threads of the shower arm. Use your finger to smooth out the tape. Next, place the new shower head onto the shower arm and twist it clockwise by hand to secure it. Turn on the water. If leaks occur, carefully tighten with an adjustable wrench — making one-quarter turns at a time — until there are no leaks.
WALLPAPER ACCENT WALL
What you’ll need: Pre-pasted wallpaper A plastic wallpaper tray (30 inches long by 10 inches wide)
A 12-inch plastic paint guide (similar to a putty knife but wider and not as sharp so it won’t gouge your paper) Scissors
A level
A utility knife
A pencil Sandpaper (100-120 grit)
Want to add drama to a room? Try hanging bold wallpaper to create an accent wall. Even though a fair number of steps are involved, this project is still doable in one day. For beginners, Allen recommends using pre-pasted wallpaper so you don’t have to buy paste and a special applicator brush to get the wallpaper to stick.
Start by sanding the walls and cleaning away any dust or debris so no lumps show through the paper later on. Then, using a level in the vertical position, draw a straight vertical line on the wall in pencil; this is called a “plumb line.” Roll out the paper on the floor and use scissors to cut the initial paper to fit the height of the wall, plus an extra four inches. Before cutting your next piece, align it with your first piece to make sure the pattern will match. You may need to trim a few inches so the pattern lines up perfectly. Then measure and cut each consecutive strip, repeating the same technique to match the pattern.
Roll up the wallpaper so the pattern is visible and soak it in a wallpaper tray filled with lukewarm water for three to five minutes. (Check instructions per manufacturer, as times may vary.) To wet evenly, carefully slide the roll from side to side in the tray so that water flows between the layers.
Slowly remove the paper strip from the water bath and, as you unroll it, gently fold the paper so the top edge and bottom meet in the middle of the strip with the sticky sides touching each other. Do not crease it and make sure the pasted sides line up evenly so the paper does not dry out along the edges; this lets the glue set. Let the paper sit in the wallpaper tray for another two to three minutes, or as directed by the manufacturer.
Before putting the paper on the wall, remove any outlet and switch covers. (Cut the power beforehand.) Then gently unroll the paper strips onto the wall, working your way from top to bottom, and keeping the edge of the paper aligned with the plumb line. Match the pattern as closely as possible. As the wallpaper sets, you can use a 12-inch paint guide to remove any bubbles and carefully cut around any electrical outlets.
Finally, hold the paint guide along the top edge, where the ceiling meets the wall, and cut excess paper off with a utility knife. Repeat at the bottom of the wall, along the top edge of the baseboard. Replace the outlet and switch covers.
EDGE GARDEN BEDS
What you’ll need: A flat-edged shovel String
Mulch
You don’t need a green thumb to edge your garden, a simple process that entails forming borders to separate your lawn from your plantings. These borders, or “edges,” will give your garden a crisp, clean look.
First mark the boundaries of the bed using string. Then take a flat-edged shovel and slice into the turf repeatedly, along the string, until you’ve outlined the entire bed. Don’t rush; just gently pull back on the shovel to loosen the earth. Remove the loosened dirt with your hands and lay down two to three inches of fresh mulch along the edge of the boundaries before removing the string.