A primer for maintaining tools for the garden
Spring is just around the corner, and it’s time to make sure your garden tools are in peak condition. Good maintenance not only prolongs the life and usefulness of garden tools; it also improves their performance in the garden. In addition, clean tools help prevent the spread of disease. Maintaining tools is as important as any other job in the garden. It’s not difficult, and if done as a twostep process takes only a few minutes.
Step one
Cleaning: Make sure shovels, trowels, hoes, and other tools used for digging or raking are free of mud and dirt. Dirt contributes to the spread of soil-borne disease and attracts moisture which can lead to rust. A damp rag or a quick spray from the hose may be all that’s needed. If mud is caked on the tool, a barbecue grill brush works well to thoroughly clean caked-on dirt. Wipe down the tool with a dry towel or let it air dry after cleaning with water. After the tool is dry, spray or lightly coat it with vegetable spray or another plant-based oil to help prevent rust. Avoid petroleum-based oils which can be harmful to the soil. Never store a wet garden tool, as it will rust. Rust can be removed with steel wool rated 000 or 0000 or a wire brush. Soaking the tool in white vinegar overnight may be necessary to treat severe rust. After soaking, remove the tool, rub with a damp rag, dry, and remove the rust with the wire brush or steel wool.
If the wooden handle of a garden tool is rough, lightly sand it using a sanding sponge or medium grit sandpaper. This will keep it smooth. The handles of tools are often neglected and can be the cause of splinters. Apply a natural, plant-based oil (like linseed oil) a couple of times a year to keep the wood lubricated and prevent cracks. Apply with a clean rag until the handle no longer absorbs the oil. This may take several coats, depending on the dryness of the handle.
Handles receive lots of stress over time and can crack if not cared for. If your tool handle is cracked, it’s time for a replacement handle. Make sure to thoroughly clean fiberglass and plastic handles and check for any damage. Replace if necessary.
Pruners, loppers and other hand tools require the same care as long-handled tools after use. Using a foaming household cleaner is helpful because of the moving parts on hand-held tools. Spray, allow to soak in, wipe down with a clean rag or use a wire brush if the tool is covered in a heavy residue. Make sure to wipe down the tool or let it air dry in the sun.
Step two
Sharpening: Dull blades cause stress on the tool and make it more difficult to use. If you are uncomfortable with sharpening them yourself, tools can be taken to a professional, although keeping tools sharp is not difficult. The trick is to go slow and to stabilize your cutting blades in a vise. It’s important to follow the factory angles (bevels), when resharpening your tool. Not all angles are the same; they differ depending on the use of the tool.
Wear safety glasses and gloves to prevent injury and make sure the tool is free of dirt. Push the file from your body at a 45-degree angle, following the factory edge of the blade. After you follow this bevel four to five times, you’ll see the blade shine up. An even stroke is what you’re aiming for when using a file.
There are a few types of files, including: flat mill files, round or half-round files, whetstones and pocket files. The type of file used will probably depend on what needs to be sharpened.
A hand pruner can be sharpened with a smaller file, while a 10-inch mill file may be more appropriate for a shovel’s edge. Sharpen only the inside edge of a shovel. Sharpening both sides of the shovel reduces both effectiveness and stability. The goal is to sharpen the shovel’s edge without taking off too much metal. Once sharpened, it is important to oil the blade to prevent rust.
When sharpening hand pruners, you may want to loosen the pivot bolt to separate the blades. If using a small pocket file, this will not be necessary. Make sure the pruners are clean and rust free. A vise is a helpful stabilization tool. When using a vise, make sure the pruners are positioned so the cutting edge receives the proper bevel. A useful tip for following the bevel is to use a marker to color the edge and file until the color is gone.
The Master Gardeners of San Diego County have a helpful short video demonstrating the tool sharpening process on their website at mastergardenersd.org.
Sanitization is an extremely import practice in the garden. It should be done before pruning and when moving from plant to plant. Sanitization helps prevent the spread of viruses, cankers and vascular system diseases that affect the health of the garden. Clorox wipes and disinfectant sprays can be used, as well as rubbing alcohol or a home-made 10% bleach solution using onepart bleach to nine parts water. Rubbing alcohol should be 70-100% isopropyl or ethanol alcohol. Chlorine bleach can be corrosive and may cause pitting to your pruner’s blades over time. These pits may harbor microbes that damage plants. If using a bleach solution or Clorox wipes, be sure to clean your tools with soap and water before putting them away.
Equipment list
The equipment need for maintaining tools includes:
• Safety glasses
• Gloves
• Sandpaper, steel wool, wire brush
• Disinfectant
• Plant-based oil
• Bench vise
• Files
• Clean rags, dish soap
With proper maintenance, garden tools should last a lifetime.
The UC Master Gardeners of Butte County are part of the University of California Cooperative Extension system, serving our community in a variety of ways, including 4H, farm advisors, and nutrition and physical activity programs. To learn more about UCCE Butte County Master Gardeners, and for help with gardening in our area, visit https://ucanr. edu/sites/bcmg/. If you have a gardening question or problem, call the hotline at 538-7201 or email mgbutte@ ucanr.edu.