Automobile Technology & Material
机器人滚边成型模拟仿真分析应用研究
张强
⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯张强
Application Research on Simulation Analysis of Robotic Roller Hem Forming⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯⋯zhang Qiang
101300) (北京汽车股份有限公司,北京
摘要:首先介绍了机器人滚边成型模拟仿真分析应用的目的,结合某车型机盖详细介绍了机器人滚边成3型模拟仿真分析的过程包括引起成型缺陷的原因及设变方案,最后采用理论分析结果与 次实物实测结果进行对比分析,验证模拟仿真分析方法有效并进一步说明在产品开发前期进行滚边成型模拟仿真分析可以缩短后期质量培育周期。
关键词:滚边成型 仿真分析 同步工程 机盖
中图分类号:U466 文献标识码:B 10.19710/J.cnki.1003-8817.20200313
DOI:
Application Research on Simulation Analysis of Robotic Roller Hem Forming
Zhang Qiang
(BAIC Motor Corporation Limited, Beijing 101300) Abstract:firstly, the purpose of simulation analysis and application of robot flanging forming is introduced, and the process of simulation analysis of robot flanging forming is introduced in detail, including the causes of forming defects and the design change scheme. Finally, the theoretical analysis results are compared with the 3 physical test results to verify the effectiveness of the simulation analysis method, and further explain the application in product development, the simulation analysis of roll forming in the early stage can shorten the quality cultivation period in the later stage. Key words: Roller forming, Simulation analysis, Simultaneous engineering, Hood
1 前言
消费者对汽车感知质量的反馈很大程度上决定了其是否对观感车辆产生购买意向,而汽车开闭件的间隙面差以及分缝周边的面品质量对汽车的感官质量影响很大。各大主机厂都采用不同的方法来保证上述品质。机器人滚压包边技术的出现是目前汽车市场发展趋势的必然产物。其成本低,占地面积小,柔性好等优点逐渐取代传统压力机包边模具占地多,能耗大,投资成本高等缺点[1]。介绍了采用机器人滚边成型模拟仿真分析的方法
在产品开发初期提高开闭件总成的品质。该方法是应用有限元软件进行成型分析,数值模拟机器人滚边成型过程,模拟滚边成型后的结果,预知滚边后成型缺陷。此种滚边成型分析方法在国外主机厂如奔驰、宝马及大众等已成熟应用,但在国内主机厂很少有应用。介绍在机盖上实施机器人滚边成型模拟仿真分析方法的过程及结果以供大家研讨。
2 机器人滚边成型模拟仿真分析应用的目的
我司未应用此方法前平均车型遗漏开闭件滚
作者简介:张强(1980—),男,工程师,硕士/学位,研究方向为焊装同步工程。
参考文献引用格式:
张强. 机器人滚边成型模拟仿真分析应用研究[J].汽车工艺与材料,2021(7):25-32.
Zhang Q. Application Research on Simulation Analysis of Robotic Roller Hem Forming[j]. Automobile Technology & Material, 2021(7): 25-32.